» Site Navigation
0 members and 650 guests
No Members online
Most users ever online was 47,180, 07-16-2025 at 05:30 PM.
» Today's Birthdays
» Stats
Members: 75,909
Threads: 249,113
Posts: 2,572,172
Top Poster: JLC (31,651)
|
-
Registered User
UTH temperature question
I'm curious to know what people have their UTH's temp set to on their thermostat. I don't have a temp gun yet so I can't be totally accurate as to what the surface temperature on the bedding is, I just have to judge it by feel. So what do you have your thermostat temp set to and how thick is your bedding? I'd just like a reference to go by before I get my temp gun. Thanks!
-
-
Registered User
I taped a thermometer sensor directly on the bottom of the tub and adjusted the thermostat to the desire degree. Then I obviously removed the tape and thermometer. But of course, a temp-gun is the best choice and more convenient. I use newspaper as substrate, which isn't thick at all.
-
The Following User Says Thank You to DPBallPythons For This Useful Post:
-
Re: UTH temperature question
 Originally Posted by ACP123
I don't have a temp gun yet so I can't be totally accurate as to what the surface temperature on the bedding is, I just have to judge it by feel.
This is wrong in so many ways.
1-you are 98 degrees, this is too hot for your snake and you cannot judge 89-95 degrees by feel.
2-it is NOT the surface temp of the bedding you need to worry about. You need to worry about the hottest point that your snake can touch (YES THEY WILL BURROW), so it under the bedding where you should measure.
-
The Following 2 Users Say Thank You to PitOnTheProwl For This Useful Post:
ACP123 (08-11-2013),led-zep (01-06-2014)
-
UTH temperature question
The temp on a thermostat probably will be different based on what kind of material the UTH is hooked up to. Also the type of thermostat will most likely affect this as well.
For me, my heat tape on both of my T8's that are made from a type of PVC, they are both set to 103 degrees. This gives my a warm spot of 89-91 degrees.
As for substrate, you want it between 1/4 - 1/2 inch thick to make sure the heat is able to penetrate the substrate and reach the snake. Like the above poster mentioned as well, balls like to burrow. With this said, you need to measure the temperature that your snake has the ability to reach, surface temperature.
I would most likely leave off the UTH until you can verify the temperature it's putting out, if you do use it, I would probably set it to 80 degrees until I could verify the temp output.
Last edited by martin82531; 08-11-2013 at 10:39 AM.
0.0.1 Normal Ball Python
1.0 Albino Ball Python
0.1 Het Snow BCI
1.0 Lesser Ball Python
-
The Following User Says Thank You to martin82531 For This Useful Post:
-
Registered User
Re: UTH temperature question
 Originally Posted by PitOnTheProwl
This is wrong in so many ways.
1-you are 98 degrees, this is too hot for your snake and you cannot judge 89-95 degrees by feel. 
2-it is NOT the surface temp of the bedding you need to worry about. You need to worry about the hottest point that your snake can touch (YES THEY WILL BURROW), so it under the bedding where you should measure.
That's my point, I can only judge the surface by feel since I don't have a temp gun and that's inaccurate. That's why I'm asking what others have their UTH's temp on. Anyway, how hot should it be under the bedding? And how deep is the bedding you use?
-
-
Registered User
Re: UTH temperature question
Thanks guys for replying, I took your advice and put the thermometer sensor on the bottom of the tub (it was previously taped directly on the UTH) then adjusted the thermostat to 90 degrees. I feel really stupid for not putting the sensor on the bottom of the tub in the first place lol.
-
The Following User Says Thank You to ACP123 For This Useful Post:
PitOnTheProwl (08-11-2013)
-
Registered User
Don't feel stupid... We have all been where you are and learned as we went along. You were smart enough to ask and get the right answer, as apposed to many who don't bother asking until it's too late and we get pics of snakes with some nasty burns.
-
-
Re: UTH temperature question
 Originally Posted by ACP123
That's my point, I can only judge the surface by feel since I don't have a temp gun and that's inaccurate.
That is my point, you cant.
 Originally Posted by ACP123
That's why I'm asking what others have their UTH's temp on.
What works in my house wont be the same in yours, too many variables. One of my racks is set at 98 and another is set at 108, identical set-ups just different locations of the room.
 Originally Posted by ACP123
Anyway, how hot should it be under the bedding?
No hotter than 95 degrees PERIOD, that is the surface your snake can touch.
 Originally Posted by ACP123
And how deep is the bedding you use?
Paper towels
-
-
Re: UTH temperature question
You most definitely cannot judge it by feel. I have an UTH for my dubia roaches that is unregulated. I felt it and it's never felt all that warm, I checked with a temp gun and it's over 115 degrees!
Sent from microwave via Tapatalk ll
Balls:
*0.1 Mojave *0.1 Pinstripe *0.1 Bumblebee *1.0 Super pastel butter *1.0 Mojave orange ghost *0.3 100% het orange ghosts *0.1 Pastel 50% het orange ghost *1.1 PE Lemonback fires *1.0 Fire *0.1 Pastel *1.0 Albino *0.1 Spider 100% het albino
Other critters:
*1.0 Anery motley corn *G. rosea tarantula *G. pulchripes *P. metallica *0.0.2 A. versicolor *C. cyaneopubescens *A. geniculata *B. smithi *B. boehmei *Nhandu chromatus *H. maculata *C. marshalli *1.0 Australian shepherd mix
-
-
Registered User
Re: UTH temperature question
My bp doesn't really like her heat lamp but loves the heat rock. Yet she doesn't really move around the cage? Is she just lazy?
-
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|