» Site Navigation
0 members and 648 guests
No Members online
Most users ever online was 47,180, 07-16-2025 at 05:30 PM.
» Today's Birthdays
» Stats
Members: 75,905
Threads: 249,104
Posts: 2,572,098
Top Poster: JLC (31,651)
|
-
Re: Helix thermostat- where to put the probe
 Originally Posted by tiexecutioner
well i tried your way again and it actually worked out pretty good with the probe on the heat tape. Inside the tub 94 degrees should feel only warm to out touch, not hot right?
Yes it should not feel hot but verifying with a digital thermometer or temp gun is the proper way to go about it.
~*Rich
1.0 100% Het Albino
1.3 Normal
1.0 Spider
0.1 Mojave
1.0 Pastel 100% Het Goldfinger
0.1 Pastel 66% Het Goldfinger
0.1 Pastel PH Goldfinger

-
-
Registered User
Re: Helix thermostat- where to put the probe
yep i did with it like 1 in abovee the unprinted newspaper it red 94.4
-
-
Registered User
Re: Helix thermostat- where to put the probe
if i click the temp gun one time it will read 94, then 95, then 94, then 96, then 94, then 95, is my temp fluctuating like crazy or is this just the temp gun?
-
-
Re: Helix thermostat- where to put the probe
Make sure you're holding the temp gun close enough. They have a ratio depending on the model you buy. The temp gun is also reading surface temps so they can vary a bit depending where in the tub you're checking.
If you're using paper as a substrate make sure there is a hide or something in there holding it down when you're measuring temps. I personally keep my hot spot in the 90-92 range. There is nothing wrong with 94 but if it consistently hits 96 it might be a tad too hot.
~*Rich
1.0 100% Het Albino
1.3 Normal
1.0 Spider
0.1 Mojave
1.0 Pastel 100% Het Goldfinger
0.1 Pastel 66% Het Goldfinger
0.1 Pastel PH Goldfinger

-
-
Registered User
Re: Helix thermostat- where to put the probe
ahhh finaly after 3DAYS i finally got it at a perfect non fluctuating temp of 93.3 degrees
-
-
Re: Helix thermostat- where to put the probe
 Originally Posted by tiexecutioner
ahhh finaly after 3DAYS i finally got it at a perfect non fluctuating temp of 93.3 degrees
Patience and persistence are the key to this hobby 
Congrats.
~*Rich
1.0 100% Het Albino
1.3 Normal
1.0 Spider
0.1 Mojave
1.0 Pastel 100% Het Goldfinger
0.1 Pastel 66% Het Goldfinger
0.1 Pastel PH Goldfinger

-
-
Registered User
Re: Helix thermostat- where to put the probe
In my new rack I am going to have extra tubs so I amthinking about just putting the probe in that tub with the same amount of substrate and set it to 94*. That way I don't have to do the trial and error of seeing how much heat is lost between the heat tape and the enclosure or risk the probe getting displaced.
6.21 ball pythons
0.1 Suriname BCC, Florida Redtail line
Lots of ASFs
-
-
Registered User
Re: Helix thermostat- where to put the probe
thats what i did and it worked perfactly, i judt didnt do it and put the probe on the heat tape because i needed the extra room, if u have extra room go for it
-
-
Registered User
Re: Helix thermostat- where to put the probe
is it ok for a adult bp in a 41q tub that i have one strip of 3"heat tape in the hot side? Can the bp have the 3" tape run down the middle of its body, and that will heat all of it?
-
-
Registered User
Re: Helix thermostat- where to put the probe
-
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|