» Site Navigation
0 members and 811 guests
No Members online
Most users ever online was 47,180, 07-16-2025 at 05:30 PM.
» Today's Birthdays
» Stats
Members: 75,905
Threads: 249,104
Posts: 2,572,101
Top Poster: JLC (31,651)
|
-
Re: What is your incubation temp?
I go 88 degress to allow room for warming up. I have alot of reptile enclosures in my snake room and it gets a little warm and incubator gets up to 91 sometimes. Mine average 55 days.
-
-
Re: What is your incubation temp?
I go at 87. It was recently chilly, and since I have the probe on the FW in the Inc. and not inside the egg tubs, that is why it has been 86.5 the past few days. But it is maintaining at 87 now. I am just paranoid about eggs being cooked to death, as I had that happen with a crappy hovabator recently. But this seems to be working fine. Like Raul said, if our house heats up a few degrees, they will not go into the danger zone.
-Jen. Back in the hobby after a hiatus!
Ball pythons:
0.1 normal; 1.1 albino. 1.0 pied; 0.1 het pied; 1.0 banana.
-
-
BPnet Veteran
Re: What is your incubation temp?
 Originally Posted by Ginevive
I go at 87. It was recently chilly, and since I have the probe on the FW in the Inc. and not inside the egg tubs, that is why it has been 86.5 the past few days. But it is maintaining at 87 now. I am just paranoid about eggs being cooked to death, as I had that happen with a crappy hovabator recently. But this seems to be working fine. Like Raul said, if our house heats up a few degrees, they will not go into the danger zone.
I don't know if this is done a lot, but a breeder I bought my albino from filled his incubator with water bottles. It takes a lot longer for 90 degree water to warm up or cool down, so it stablizes the temperature in case there's fluctuations. That water is always giving off 90 degree heat, even during power outages, or crappy hovabators.
-
-
BPnet Veteran
Re: What is your incubation temp?
that is true...bricks that you can pick up at lowes or homedepot for cheap work just as well if not better... you can take them out as you get more eggs but the more area filled up in the incubator leaves less room for temp change

if you cant afford to take care of it, dont get it
-
-
BPnet Veteran
Re: What is your incubation temp?
88 degrees
-
-
Re: What is your incubation temp?
 Originally Posted by bait4snake
I don't know if this is done a lot, but a breeder I bought my albino from filled his incubator with water bottles. It takes a lot longer for 90 degree water to warm up or cool down, so it stablizes the temperature in case there's fluctuations. That water is always giving off 90 degree heat, even during power outages, or crappy hovabators.
I also put tubs with rocks and water in my incubators which becomes my bottom shelf. The tubs have holes near the top so they help stabilize temps and humidity. It is very dry where I live so I am always concerned that it will dry out in there. I hand squeeze all my vermiculite until ALL the excess water drips out(good excersize LOL), then put it in the incubator for a day or two for temps to adjust and then it's ready for eggs. Alll my beardie and BP eggs have had 100% success rate with this method. Although I am concerned they may dry out I am aware that too much water(in the vermiculite) is the killer!
-
-
Re: What is your incubation temp?
I definately have the water bottles in mine. They help a lot.. there really has been little to no fluctuation.
I have a weirds system that I will attempt to describe. My tubs are pretty prone to condensation with the variating between their inner temperature (the incubating temp) and the FW and its probe. Every 2 days I open them up and wipe off the excess condensation. It also seems to give the eggs some fresh air. I do it fast, and there is really little variation in temperature while I do so. I actually melted 2 small holes into the egg-tub lids before putting the eggs in; it helps to reduce the condensation also. But my medium (verm and perlite) is not sopping wet; like Raul, I wrung it out till all of the water was dripped out.. it still creates the condensation, but by wiping that, and sometimes adding incubator-temperature water into the corners of the medium (only had to do that once) things are stable and going good! It might be a little different than the norm, but it is working so far.
I also think that the opening of the tubs mimics what an incubating mom would do in the wild; she leaves the eggs for an occasional drink or to defecate. So I would guess that the temp would go down a little during that time; but again, the room is warm where the eggs are and it Never goes into the danger zone.
-Jen. Back in the hobby after a hiatus!
Ball pythons:
0.1 normal; 1.1 albino. 1.0 pied; 0.1 het pied; 1.0 banana.
-
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|