He STILL won't eat

[Zincubus]

Yes there is a heat mat with a thermostat. The heat lamp was getting way too hot, so I ditched it for the time being. As for the water dish, I still have to switch it out.

You mentioned 'the' temp was 72F !?

What temp is that again - the warm , cool or ambient ?

It's getting rather puzzling to be honest.

What exactly are you using to take the warm hide surface temps again ??

Sent from my iPhone using Tapatalk

[FlipsideRuffian]

You mentioned 'the' temp was 72F !?

What temp is that again - the warm , cool or ambient ?


Sent from my iPhone using Tapatalk

Oh no no no, that's the ambient!! The heat lamp made the tank way too hot in the high 90s, so I turned it off until I can figure out how to adjust it. The heat mat stays in the 80s, but if that's not right please tell me.


Sent from my iPhone using Tapatalk

[Zincubus]

Oh no no no, that's the ambient!! The heat lamp made the tank way too hot in the high 90s, so I turned it off until I can figure out how to adjust it. The heat mat stays in the 80s, but if that's not right please tell me.


Sent from my iPhone using Tapatalk

If the warmest surface is under the warm hide and that's 80F then that's fine providing you've used a reliable thermometer..





Sent from my iPhone using Tapatalk

[MissterDog]

If the warmest surface is under the warm hide and that's 80F then that's fine providing you've used a reliable thermometer..

Sent from my iPhone using Tapatalk

Unless I’m missing something here, no 80 for a hot spot temp is not okay! It’s too low and honestly that should be a cool side temp.

Op my first question is how are you measuring that temperature exactly? Because keep in mind there is a difference between ambient and surface temperatures. In order to get an accurate surface temp for your hot spot you need to measure the temp UNDER the substrate where you heat mat is, preferably with a temp gun.

Your hot spot should be around 88-90 for optimal digestion, just make sure the hottest surface your bp can touch does not exceed 92. Again to ensure that I highly advise getting a hold of a temp gun which are fairly inexpensive on amazon.

[Zincubus]

Unless I’m missing something here, no 80 for a hot spot temp is not okay! It’s too low and honestly that should be a cool side temp.

Op my first question is how are you measuring that temperature exactly? Because keep in mind there is a difference between ambient and surface temperatures. In order to get an accurate surface temp for your hot spot you need to measure the temp UNDER the substrate where you heat mat is, preferably with a temp gun.

Your hot spot should be around 88-90 for optimal digestion, just make sure the hottest surface your bp can touch does not exceed 92. Again to ensure that I highly advise getting a hold of a temp gun which are fairly inexpensive on amazon.

I'm getting confused myself now ..

I'm posting on a Corn snake thread as well as a few others !



Apologies .. of course 80 isnt too bad for a Corn Snake but it isn't close enough to be ok for a Royal !!

I have asked a few times HOW he's measuring these temps and I still don't know the answer .
That's a big concern right there .

That said if he's going on vacation I dare say 80F maybe better than leaving that unregulated bulb pump out crazy temperatures....


I really don't know how this is gonna end up tbh ...


Maybe better leaving it in a local pet store for a couple of weeks - they do snake sitting over there , I presume ?

He could leave it there , have a vacation and sort the set up properly then get the snake back ... sorted !


Sent from my iPhone using Tapatalk

[MissterDog]

I'm getting confused myself now ..

I'm posting on a Corn snake thread as well as a few others !



Apologies .. of course 80 isnt too bad for a Corn Snake but it isn't close enough to be ok for a Royal !!

I have asked a few times HOW he's measuring these temps and I still don't know the answer .
That's a big concern right there .

That said if he's going on vacation I dare say 80F maybe better than leaving that unregulated bulb pump out crazy temperatures....


I really don't know how this is gonna end up tbh ...


Maybe better leaving it in a local pet store for a couple of weeks - they do snake sitting over there , I presume ?

He could leave it there , have a vacation and sort the set up properly then get the snake back ... sorted !


Sent from my iPhone using Tapatalk

Haha I’ve done the same thing before by mistake so no worries :p


OP does have a thermostat for their heatmat so they could adjust the temp HOWEVER I agree the uncertainty of how OP is measuring surface temps is concerning, even more when vacation is limiting options and time for adjustments. Very tricky situation

Not entirely sure how much I’d trust a local pet shop for sitting given how most employees are not knowledgeable and could make things worse. That and the possibility of getting mites. It’s another option at least but not without risks. Unless OP could hire a pet sitter familiar/experienced with snakes to look after them?

OP we wish you luck and hope for the best so when you return from vacation you can get everything sorted if you are unable to before leaving.