Probe placement on radiant heat panel :)

[dylan815]

Hey ya'll. Just got my radiant heat panel in the mail today from pro products. I have a herp stat intro thermostat that i want to use with this panel. My question is where do i put the probe?? thanks for you help!

[CALM Pythons]

Mine comes through the back wall (where pro panel cord goes too) and over the top of pro panel between ceiling and pro panel then hangs 1/2 way between floor and ceiling. I'll see if i can find a pic. Then my thermometer probe is on the hot aide and thermometer is mounted on cool side for cool ambient.


Sent from my iPhone using Tapatalk

[CALM Pythons]

Here you see my RHP probe hanging on the Hot Side over the RHP and other pic my thermometer mounted on opposite side. The thermometer probe runs out the back and comes in on the hot side and under my substrate on the floor, its mounted under the hot hide.


Sent from my iPhone using Tapatalk

[SiXandSeven8ths]

Just drop it in from the top, a few inches or so below the panel. Adjust your thermo from there. I find my sensor to read just a few degrees different from the floor temp, I get a nice floor temp with good ambient.

[Deu2e]

Here you see my RHP probe hanging on the Hot Side over the RHP and other pic my thermometer mounted on opposite side. The thermometer probe runs out the back and comes in on the hot side and under my substrate on the floor, its mounted under the hot hide.


Sent from my iPhone using Tapatalk

Hey i have not hooked my rhp up yet, but i have a question. When i talked to bob over at pro products he said i should place the probe for the rhp on the cool side and away from the heat source, so i can have the rhp temp for the cool side at the desired temp. Is this also an option. Im waiting on my herpstat redline to arrive so i can finish the t8 build.

Sent from my SM-J727P using Tapatalk

[CALM Pythons]

That's another way to do it yes didn't work for me depends on your normal house temperature in the room the enclosures in and also depends on the size of the cage T8 is much smaller than mine so that may be the way to go I trust what Bob says


Sent from my iPhone using Tapatalk

[Deu2e]

That's another way to do it yes didn't work for me depends on your normal house temperature in the room the enclosures in and also depends on the size of the cage T8 is much smaller than mine so that may be the way to go I trust what Bob says


Sent from my iPhone using Tapatalk

Thanks a lot. I have another question it may be a dumb question but im a lil confused being this is my first rhp. Ap mounted my rhp for me but i dont see a power cord? I only see the white cord its attached to im assuming this is the cord i clamp into the little white locks and insert in my herpstat right? And the power will be coming right from my herpstat? Sorry is this is a dumb question..

Sent from my SM-J727P using Tapatalk

[dylan815]

Thanks a lot. I have another question it may be a dumb question but im a lil confused being this is my first rhp. Ap mounted my rhp for me but i dont see a power cord? I only see the white cord its attached to im assuming this is the cord i clamp into the little white locks and insert in my herpstat right? And the power will be coming right from my herpstat? Sorry is this is a dumb question..

Sent from my SM-J727P using Tapatalk

My pannel didn't come with a finished plug in. Just a white cord and a seprate plug in piece. Just put the wire in the plug in and squish it in. Then plug that into your herpstat and plug your herpstate into a wall!

[SDA]

If you got it from RBI (not sure if pro products does the same style cord), the second page here shows how to install the power cord

http://www.reptilebasics.com/manuals/heatpanel_inst.pdf

[dylan815]

If you got it from RBI (not sure if pro products does the same style cord), the second page here shows how to install the power cord

http://www.reptilebasics.com/manuals/heatpanel_inst.pdf

They both have similar power cord installation.