underbelly peeling/flaking? please help!

[chrid16371]

A heat mat is nothing more than two thin pieces of plastic put together with some sort of heating element in the middle.

If the OP has a tstat placing the probe on the bottom can and will work just fine. It has been done many times and sometimes we even suggest it over placing the probe in the middle if the probe is large. We do this to keep the uth in contact with the cage floor and not create a cool spot in the middle from lack of contact.

My intellitemp mats are about the same temp top and bottom and I just opened 3 unused zoo med spares and tested those and one was 12 degrees cooler on bottom another 17 degrees cooler on bottom and the last 13 degrees cooler on bottom. This was the reason I asked for the brand. I remember testing zilla, flukers, zoomed, Kane, intelltemp awhile back but couldn't find where I put my results so I decided to test a couple spares I had, unfortunately I don't have all the brands I had then. All these test I used 3 different temp guns to confirm Maybe this is the reason the thermostat let her hot spot get up to 111 degrees. Not only that but if you have a sensitive thermostat like a herpstat all it takes is a window open and cool air blowing over the exposed probe to raise the temps. This has happend a few times with my herpstat probe for the rhp when opening the cage or misting so I moved it and all is fine now. I have a dead zoomed uth I will be dissecting tomorrow to see if there is a reason the heat is more concentrated upwards instead of evenly both ways.

[KMG]

My intellitemp mats are about the same temp top and bottom and I just opened 3 unused zoo med spares and tested those and one was 12 degrees cooler on bottom another 17 degrees cooler on bottom and the last 13 degrees cooler on bottom. This was the reason I asked for the brand. I remember testing zilla, flukers, zoomed, Kane, intelltemp awhile back but couldn't find where I put my results so I decided to test a couple spares I had, unfortunately I don't have all the brands I had then. All these test I used 3 different temp guns to confirm Maybe this is the reason the thermostat let her hot spot get up to 111 degrees. Not only that but if you have a sensitive thermostat like a herpstat all it takes is a window open and cool air blowing over the exposed probe to raise the temps. This has happend a few times with my herpstat probe for the rhp when opening the cage or misting so I moved it and all is fine now. I have a dead zoomed uth I will be dissecting tomorrow to see if there is a reason the heat is more concentrated upwards instead of evenly both ways.

Even if the temp is lower on the bottom than the top, the tstat will still control the uth. Just instead of having to set the tstat at a higher temp to account for the upper temp you would set it lower to account for the lower bottom temp. Still works the same.

As long as the hotspot is properly checked and the temp known it will not matter if the probe is on top or bottom. I personally like to have the probe on top but sometimes the bottom just works better.

I have no clue what the OP had setup or has done with the little information we have been given and expected to help. I feel as if there is more to this story than they care to reveal.

[chrid16371]

Even if the temp is lower on the bottom than the top, the tstat will still control the uth. Just instead of having to set the tstat at a higher temp to account for the upper temp you would set it lower to account for the lower bottom temp. Still works the same.

As long as the hotspot is properly checked and the temp known it will not matter if the probe is on top or bottom. I personally like to have the probe on top but sometimes the bottom just works better.

I have no clue what the OP had setup or has done with the little information we have been given and expected to help. I feel as if there is more to this story than they care to reveal.

Very true. The thing is some people go solely off what the tstat says or what other people set it and don't check with temp guns or anythjng so it doesn't always come out with the same results bc everyone's environmental factors, substrate, etc are not the same. In one of the zoo meds I tested (let's say the one that was 17 degrees cooler on bottom) if you put the probe on the bottom and set it to 95, bc that's what someone told you they ran it at, the top of the uth thats setting directly on the tank would be running at 112 which would be way to high. Yes this could be solved by lowering the tstat but let's face it some people don't check there temps properly and like I said above go solely on what other people say just to save themselves the $12 to buy a probed thermometer. This is why I think its safer and why I give the advice to put the probe in between uth and enclosure that way if they go by what someone else told them it would be at a safer temp. I'm so ocd about my temps I use 8 acurite thermometers, 4 for each of my bp. Of course there not all in the same spot and do there job of telling me the temps inside and outside hides and under and on top substrate. I know its a little overboard but I still don't get why people can't pick up 1 while I'm sitting here with 8 and that's just for my bps.

But yes I do agree with you they can be used top or bottom when monitored correctly. I also agree there is more to the story then what is being shared. Hopefully the problems are addressed and the snake continues on to a healthy life.