» Site Navigation
0 members and 642 guests
No Members online
Most users ever online was 47,180, 07-16-2025 at 05:30 PM.
» Today's Birthdays
» Stats
Members: 75,903
Threads: 249,097
Posts: 2,572,069
Top Poster: JLC (31,651)
|
-
BPnet Veteran
Hides
I found these small sterilite tubs at Walmart the other day that are the perfect size hides for juvie to sub-adults, the only problem is that they only come in clear. So I was wondering if anyone had any advice on how I could black them out safely. 
0.1 Lesser 1.2 Enchi Lessers 0.1 Enchi Spinner 0.1 Enchi 0.1 Super Enchi 0.3 Pastels 0.1 Firefly 0.1 Super Pastel Yellowbelly
1.1 Pastel Soul Sucker 1.2 Bumblebee 0.1 Fire 0.1 Super Fire 3.3 100% Double Het Albino/Pied 0.2 Mojave 1.0 Pastel Enchi Mystic 0.1 Mystic 0.1 Mystic Potion 0.1 Queenbee 1.0 Blackhead 0.1 Pinhead 0.4 Normals 0.1 Pastel Superstripe 0.1 Orange Dream Yellowbelly 1.0 GHI Yellowbelly 1.0 Crystal 1.0 Leopard Ivory 1.1 Pastel HGW 0.1 Special 0.1 Bling Yellowbelly 0.1 Chocolate Lesser 1.0 Clown 0.1 Butter Leopard het Ghost 0.1 Freeway
-
-
Krylon sells a paint that is specifically for plastic, but I'm not sure I would trust it around my snakes. Even after it's dry is could continue to off-gas...but then again, so does plastic.
Thomas "Slim" Whitman
Never Met A Ball Python I Didn't Like 
-
-
Go to Wal-Mart and get some stick-on contact paper and stick it to the outside of the tubs to black it out.
1.0 Boxer (Boba…@bobatheboxer on IG)
-----------------------------------------------------------------
"Blaming the leader of the fools should not blind anyone to the vast confederacy of fools that made him their leader."
~unknown~
-----------------------------------------------------------------
SUPPORT OUR WOUNDED WARRIORS
-----------------------------------------------------------------------------------------------------------
-
-
I would be very very careful about using anything with an adhesive backing in a snake enclousure.
Thomas "Slim" Whitman
Never Met A Ball Python I Didn't Like
-
-
Re: Hides
 Originally Posted by Slim
I would be very very careful about using anything with an adhesive backing in a snake enclousure.
Exterior Slim not on the inside.
1.0 Boxer (Boba…@bobatheboxer on IG)
-----------------------------------------------------------------
"Blaming the leader of the fools should not blind anyone to the vast confederacy of fools that made him their leader."
~unknown~
-----------------------------------------------------------------
SUPPORT OUR WOUNDED WARRIORS
-----------------------------------------------------------------------------------------------------------
-
-
Edit: Just went back and re-read your post. You're talking about blacking out the tubs...he was talking about blacking out the hides. I understand the disconnect now. My bad for not reading your post more closely.
Last edited by Slim; 03-14-2012 at 02:06 PM.
Thomas "Slim" Whitman
Never Met A Ball Python I Didn't Like
-
-
Like what LGrey23 did:
Originally Posted by LGray23
Then I cut the Con-tact paper to fit along the two sides and back of each container. Place along each side and back, this can get tricky as air bubbles like to get between the plastic and adhesive. (If you aren't using the Con-tact paper, spray paint the sides and back of the container, you may need more than one can!)
1.0 Boxer (Boba…@bobatheboxer on IG)
-----------------------------------------------------------------
"Blaming the leader of the fools should not blind anyone to the vast confederacy of fools that made him their leader."
~unknown~
-----------------------------------------------------------------
SUPPORT OUR WOUNDED WARRIORS
-----------------------------------------------------------------------------------------------------------
-
-
Re: Hides
Originally Posted by RetiredJedi
Like what LGrey23 did:
Roger That! Again, tubs vs. hides.
Thomas "Slim" Whitman
Never Met A Ball Python I Didn't Like
-
-
Re: Hides
Originally Posted by Slim
Roger That! Again, tubs vs. hides.
hehehe, yea I went back and saw your post edit. Guess my reading comprehension is bad today. I had to go back and realize the OP was talking about the hides and not the tubs...
Last edited by RetiredJedi; 03-14-2012 at 02:12 PM.
1.0 Boxer (Boba…@bobatheboxer on IG)
-----------------------------------------------------------------
"Blaming the leader of the fools should not blind anyone to the vast confederacy of fools that made him their leader."
~unknown~
-----------------------------------------------------------------
SUPPORT OUR WOUNDED WARRIORS
-----------------------------------------------------------------------------------------------------------
-
-
BPnet Veteran
Re: Hides
Ya those were the only two ideas I could come up with too but neither seem very safe to me and I don't want anything to happen to my babies.
0.1 Lesser 1.2 Enchi Lessers 0.1 Enchi Spinner 0.1 Enchi 0.1 Super Enchi 0.3 Pastels 0.1 Firefly 0.1 Super Pastel Yellowbelly
1.1 Pastel Soul Sucker 1.2 Bumblebee 0.1 Fire 0.1 Super Fire 3.3 100% Double Het Albino/Pied 0.2 Mojave 1.0 Pastel Enchi Mystic 0.1 Mystic 0.1 Mystic Potion 0.1 Queenbee 1.0 Blackhead 0.1 Pinhead 0.4 Normals 0.1 Pastel Superstripe 0.1 Orange Dream Yellowbelly 1.0 GHI Yellowbelly 1.0 Crystal 1.0 Leopard Ivory 1.1 Pastel HGW 0.1 Special 0.1 Bling Yellowbelly 0.1 Chocolate Lesser 1.0 Clown 0.1 Butter Leopard het Ghost 0.1 Freeway
-
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
Reply With Quote
