Tank Setup Critique/Comments

[Praetori]

So here's our tank. It's a 20 gal long with Plexiglas glued to the mesh lid to help with ambient heat/humidity problems. Normally both logs have cardboard to enclose the open end and have wires going in the log to measure the heat inside. The humidity is from 60-65 degrees and the heat ranges from the low 80s to about 93 degrees F.

I bought a plastic ivy decoration to create a more enclosed space but my hubby disagreed and removed it. Is there anything that I should add/change? The toilet paper rolls are for the female-she loves hiding in them.

[Inugohan]

I would start by taking one of the snakes out and putting in a separate cage. Of course this is totally up to you. Great look bee by the way! Also, the substrate is not something I would use. I think you should try cocofiber/husk, or even just plain newspaper. Best of luck! ~Caylan.S.~

[Kaorte]

Well there are a few things to me are not as they should be.

The first being two snakes in one tank. Unless you are breeding them, which I hope you aren't because they both look very young, you should house the snakes separately. Ball pythons are not social animals and do not benefit by being housed together.

Second would be the half log hides. For a secretive snake like a ball python, half logs just don't cut it. Exo-terra makes a rock cave type hide that looks very nice and is suitable for ball pythons.

Third, the accurite placement. The probe should be right on the glass where the uth is. The probe should be completely under the substrate. you need to measure the hottest possible spot the snake can possibly get to to prevent thermal burns. Wouldn't want to toast one of those beautiful snakes! The rest of the unit should go on the other side of the tank (cool side). All those dial and gauge thermometers are useless, you might as well throw them away.

Other then that I think it looks like a job well done

[MitsuMike]

Tin foil on the top of the screen to help with humidity but leave a slight hole i the top. Like 1/4 uncovered the rest covered.

[Praetori]

Coconut husk and cypress mulch raised the humidity too much and that's why we're using the carefresh bedding, but I'll see how aspen or just plain newspaper works and switch it out.

Good to know about the dials, and I'll move the probe around too.

No, they're definitely not of breeding age yet-the biggest, the bee, is about 150g. She's growing fast though and I'm about to switch to either a homemade rack or I'm buying one.

As for the logs...I'll switch that out too.

[RockyTop]

Kaorte has some great advice. Thermometer Probe goes under the substrate, ontop of the UTH. This way if the snake goes moves the substrate, you know what highest temp the snake will be exposed to. Then make sure you have a thermostat hooked up to your UTH, and the probe for that is outside the enclosure on the UTH so the snake does not move it and get a temp spike. Use the thermometer to gauge what to set your thermostat up to.

I keep my apt very cool, so I have 2 UTHs hooked to a thermostat(with one hooked to a dimmer as well). Ambient air is 78-83 (cool side to warm side), and my cool hide stays exactly 11 degrees cooler than my warm hide. My warm hide fluctuates between 91-94 as it heat and cools with the thermostat, cool side is 80-83. I also use a CHE for the ambient air since I do keep my apt cool.

I had the same prob as you. Switched to aspen, and now my humidity maintains ~55%, with a bit less over the warm side where the CHE is at.

Temps and humidity are extremely important, it isn't something you want to guesstimate at, and "ball park" it.

(Now I know why people say tanks are harder to regulate! They are a bit tough until you finally get it setup correctly!)

Deborah Stewart (a reputable breeder in this community) recommended using plastic flower saucers, tubs, etc. I took this approach. I paid .25 cents a hide for 6" flower saucers, and they look fine. It provides a snug hide, which allows the snake to feel secure on all sides.

Good luck, nice looking snakes!

[RockyTop]

Coconut husk and cypress mulch raised the humidity too much and that's why we're using the carefresh bedding, but I'll see how aspen or just plain newspaper works and switch it out.

Also, you mentioned you glued plexiglass to the top. You didn't mention if you cut a hole in it to allow ventilation. If you didn't, this may be a reason for elevated humidity.