pvc enclosure refresher

[baldegale]

How often does he do shows? I see he's in Dayton as I get to Parkersburg, WV once or twice a year.

he goes to multiple shows a month. https://www.facebook.com/47959593542...5959080451364/


Sent from my iPhone using Tapatalk

[MR Snakes]

he goes to multiple shows a month. https://www.facebook.com/47959593542...5959080451364/


Sent from my iPhone using Tapatalk

Which is the one down the street from you?

[baldegale]

Which is the one down the street from you?

that one he doesnt have listed, even though i messaged him about it, but its the cleveland reptile show, thats how i found out about him in the first place


Sent from my iPhone using Tapatalk

[MR Snakes]

that one he doesnt have listed, even though i messaged him about it, but its the cleveland reptile show, thats how i found out about him in the first place


Sent from my iPhone using Tapatalk

Could it be that he is protesting LeBron's exit to L.A.?

[baldegale]

Could it be that he is protesting LeBron's exit to L.A.?

LOL maybe, hes based in cinci though


Sent from my iPhone using Tapatalk

[MR Snakes]

LOL maybe, hes based in cinci though


Sent from my iPhone using Tapatalk

Just a stroll up the 3C Highway!

[baldegale]

alright everyone, its a go on getting the enclosure and getting my hoggy back. im gonna go with pro products for my RHP even though its more money, also a funny plot twist is that my “female” hognose is now known to be a male (makes a lot of sense.) also my next question(s) are where should the RHP be located? on the roof? also what temp should it be set at and where should i put the probe? and this is @Dianne but how long does the processing and stuff take from pro products?


Sent from my iPhone using Tapatalk

[Dianne]

alright everyone, its a go on getting the enclosure and getting my hoggy back. im gonna go with pro products for my RHP even though its more money, also a funny plot twist is that my “female” hognose is now known to be a male (makes a lot of sense.) also my next question(s) are where should the RHP be located? on the roof? also what temp should it be set at and where should i put the probe? and this is @Dianne but how long does the processing and stuff take from pro products?


Sent from my iPhone using Tapatalk

Great news! So glad you’ll have your guy at home. Yes, the rhp goes on the roof/ceiling inside the enclosure. I have my probe on the back wall of the enclosure, directly under and behind the panel, about an inch and a half off the cage floor. The thermostat is set a bit lower than my actual hotspot, because the probe is not directly under the heat source. When dialing any of my panels in, I set my Accurite thermometer directly under the heat panel. The benefit to these thermometers is that they track a high/low temperature range in addition to the current temperature reading. Once my Accurite has the hot spot reading I want, I leave everything in place 24-48 hours (no snake) and then check the surface temps with my temp gun. If all is well, in goes the snake.

I ordered 3 panels on 11/15/18 and received them in early December, so I’d say 2-3 weeks turn around.

[Dianne]

Here's a photo of the panel and probe in one of my 8' cages. These cages have 2 panels due to the size, but the setup principles are the same.

Sent from my moto z3 using Tapatalk

[baldegale]

Great news! So glad you’ll have your guy at home. Yes, the rhp goes on the roof/ceiling inside the enclosure. I have my probe on the back wall of the enclosure, directly under and behind the panel, about an inch and a half off the cage floor. The thermostat is set a bit lower than my actual hotspot, because the probe is not directly under the heat source. When dialing any of my panels in, I set my Accurite thermometer directly under the heat panel. The benefit to these thermometers is that they track a high/low temperature range in addition to the current temperature reading. Once my Accurite has the hot spot reading I want, I leave everything in place 24-48 hours (no snake) and then check the surface temps with my temp gun. If all is well, in goes the snake.

I ordered 3 panels on 11/15/18 and received them in early December, so I’d say 2-3 weeks turn around.

i figured as much on the setting up, i’ll probably order within the next couple days because ill be getting the enclosure on the 20th


Sent from my iPhone using Tapatalk