» Site Navigation
0 members and 1,234 guests
No Members online
Most users ever online was 6,337, 01-24-2020 at 04:30 AM.
» Today's Birthdays
» Stats
Members: 75,137
Threads: 248,581
Posts: 2,569,047
Top Poster: JLC (31,651)
|
-
Registered User
Radiant heat panel issues
I recently set up a 48x20x15 pvc enclosure for my BP. I have a 75 watt pro products rhp mounted on the far right with the probe on the cool end about half way down. Thermostat is set to 78. The warm side is right where it should be, at 85-90. The middle temps are about 80, acting more as the cool side right now, while the actual cool side is in the low 70’s. I can’t bump up the thermostat without the warm side getting too hot, is there something I’m missing? Bob from pro products recommended I mount the panel to one side for a larger gradient but those low temperatures don’t seem appropriate. Should I try moving the probe somewhere else?
Also, I’m having an issue keeping the humidity up. I finally got it to 70 but that’s the highest I’ve been able to get it. I use a mix of eco earth, cypress mulch, and sphagnum moss.
-
-
Registered User
Who makes the cage? Sounds like you may need to block some vents off. I put my probes hanging from the ceiling, about an inch away from the heat panel, hanging an inch below the panel, on the backside between the panel and the wall and adjust accordingly to give me my hot spot. Their in their own heated room now that stays between 77-79, but when they weren’t they were upstairs where the ambients of the room were 63-64 and it kept the cool side at 77. But I had to block off half the vents to achieve this. I’m using animal plastics cages. 4’x2’ with a pro products radiant heat panel in it...75 watt I believe. You only need your humidity around 50-60%. Mine stays 70-80 with only one vent blocked off currently (5 total vents) but I have a huge water bowl in the center of the cage, partially under the heat panel, as the setup is for a green anaconda.
-
-
Re: Radiant heat panel issues
One way to look at your problem is that it is less of a heating issue and more of a heat loss issue.
We have several 2'x3'x12" RBI cages (with UTH and 80W RHP) that are stacked in front of a large window. We live in New York and in the winter we have to keep the curtains closed. If we don't, the heat loss through the window is so great our that we run in to the same problem you are experiencing. And you've got an extra foot of caging to deal with.
My advice is to try to reduce heat loss. Try covering one or more sides of your cage with foam insulation and see if that helps.
A side benefit of reducing heat loss is that your RHP won't have to work as hard and you'll save a few dollars on your utility bill.
-
The Following User Says Thank You to larryd23 For This Useful Post:
-
Registered User
Re: Radiant heat panel issues
Please post pics of your enclosure and I am sure someone will be able to help even more?
Sometimes over night my cool side will get to the low 70s also. Insulating the enclosure has helped. At night I have my RHP a little hotter as the light is off. It is a balancing act.
-
-
Re: Radiant heat panel issues
Originally Posted by larryd23
My advice is to try to reduce heat loss. Try covering one or more sides of your cage with foam insulation and see if that helps.
If you don't have foam insulation on hand, a small blanket or large towel will work if you want to test this solution.
Some of my racks are in cooler rooms during the winter. I've covered them with a light blanket when the ambient room temp can drop down to 70*F and it does help bump up the ambient temp in the tubs.
-
-
Registered User
Re: Radiant heat panel issues
Originally Posted by Waterman
Who makes the cage? Sounds like you may need to block some vents off. I put my probes hanging from the ceiling, about an inch away from the heat panel, hanging an inch below the panel, on the backside between the panel and the wall and adjust accordingly to give me my hot spot. Their in their own heated room now that stays between 77-79, but when they weren’t they were upstairs where the ambients of the room were 63-64 and it kept the cool side at 77. But I had to block off half the vents to achieve this. I’m using animal plastics cages. 4’x2’ with a pro products radiant heat panel in it...75 watt I believe. You only need your humidity around 50-60%. Mine stays 70-80 with only one vent blocked off currently (5 total vents) but I have a huge water bowl in the center of the cage, partially under the heat panel, as the setup is for a green anaconda.
I got it from a guy at an expo, there’s only one vent. The room is pretty cool, around the low 70’s. There’s definitely cool air coming in through the windows. I’ve tried blocking them off with towels and hanging heavy curtains.
Last edited by _chelseaaa; 01-24-2020 at 01:42 PM.
-
-
Re: Radiant heat panel issues
Originally Posted by _chelseaaa
I recently set up a 48x20x15 pvc enclosure for my BP. I have a 75 watt pro products rhp mounted on the far right with the probe on the cool end about half way down. Thermostat is set to 78. The warm side is right where it should be, at 85-90. The middle temps are about 80, acting more as the cool side right now, while the actual cool side is in the low 70’s. I can’t bump up the thermostat without the warm side getting too hot, is there something I’m missing? Bob from pro products recommended I mount the panel to one side for a larger gradient but those low temperatures don’t seem appropriate. Should I try moving the probe somewhere else?
Also, I’m having an issue keeping the humidity up. I finally got it to 70 but that’s the highest I’ve been able to get it. I use a mix of eco earth, cypress mulch, and sphagnum moss.
The panel is going to heat the same regardless. I use the probe on the cool side as well with zero issues. I will agree with what someone said on here is that you are losing heat. Curious as to how you are checking the temperatures throughout the enclosure? heat gun or digital stats? When you bought the panel did you tell bob everything about that specific set up?
Big things are:
Enclosure size
Ambient room temperatures
Is the cage on a concrete floor or close to one?
-
-
Registered User
Re: Radiant heat panel issues
Originally Posted by Moose84
The panel is going to heat the same regardless. I use the probe on the cool side as well with zero issues. I will agree with what someone said on here is that you are losing heat. Curious as to how you are checking the temperatures throughout the enclosure? heat gun or digital stats? When you bought the panel did you tell bob everything about that specific set up?
Big things are:
Enclosure size
Ambient room temperatures
Is the cage on a concrete floor or close to one?
The ambient temp in the room was a main concern so I made sure to mention it to him. The enclosure is on a carpeted floor. I’ll try blocking off the windows with something. There’s only one vent and it’s not very big but I’ll also try covering part of that and see what happens. Thanks!
- - - Updated - - -
Originally Posted by Moose84
The panel is going to heat the same regardless. I use the probe on the cool side as well with zero issues. I will agree with what someone said on here is that you are losing heat. Curious as to how you are checking the temperatures throughout the enclosure? heat gun or digital stats? When you bought the panel did you tell bob everything about that specific set up?
Big things are:
Enclosure size
Ambient room temperatures
Is the cage on a concrete floor or close to one?
The ambient temp in the room was a main concern so I made sure to mention it to him. The enclosure is on a carpeted floor. I’ll try blocking off the windows with something. There’s only one vent and it’s not very big but I’ll also try covering part of that and see what happens. Thanks!
-
-
Re: Radiant heat panel issues
Originally Posted by _chelseaaa
I got it from a guy at an expo, there’s only one vent. The room is pretty cool, around the low 70’s. There’s definitely cool air coming in through the windows. I’ve tried blocking them off with towels and hanging heavy curtains.
It wouldn't surprise me if the cold air leaking in through the windows makes the floor area colder than the rest of your room.
This is a terribly "redneck" solution, but I use clear plastic pieces cut from a painter's drop cloth, and clear packing tape, to seal up/cover my remaining old, poorly-insulated, single-pane windows remaining in my house (I'm slowly replacing them as finances permit). For under $10 in supplies per winter I figure I'm saving $40-50 monthly on heating bills by eliminating those drafts.
-
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|