» Site Navigation
3 members and 1,286 guests
Most users ever online was 6,337, 01-24-2020 at 04:30 AM.
» Today's Birthdays
» Stats
Members: 75,137
Threads: 248,582
Posts: 2,569,050
Top Poster: JLC (31,651)
|
-
Registered User
Were should I put the prove
I have a makeshift incubator out of a thick foam cooler and flex watt on the bottom that comes up the sides and water bottles on top of that I have the egg box, were should I put the herpestad prove in the egg box, or on the inside of the cooler?
-
-
Registered User
Re: Were should I put the prove
Here come I with pure speculation...
I'd guess directly on your heat source. The concern in the usual setup for a snake is that the snake will do something to make the thermostat think it needs to run the heat source way more than it actually has to. In an incubator, that isn't a concern, so I'm thinking it may be safe to put it in the egg box. However, when the eggs do hatch, that immediately becomes a concern, so it's probably safer to put it directly on the heat source and use a thermometer or temp gun on the target area.
Most questions are answered here.
GENERATION 25:
The first time you see this, copy it into your sig on any forum and add 1 to the generation. Social experiment.
1.0 '10 cinnamon bp
1.0 Coluber constrictor constrictor
1.1 gargoyle geckos
0.2 normal bp
0.1 beautiful normal bp RIP
1.0 '04 het pied bp RIP
-
The Following User Says Thank You to stevepoppers For This Useful Post:
martinarquero (05-26-2010)
-
Re: Were should I put the prove
The probe in my inc is taped under the flexwatt directly against it.
Jerry Robertson
-
The Following User Says Thank You to snakesRkewl For This Useful Post:
martinarquero (05-26-2010)
-
Re: Were should I put the prove
I put it right on top of the eggs in the egg box. I don't care what the temps are on the heat source I want to know what temps the eggs are. Of course in a large incubator with several egg boxes it's a little different. My setup was a little different. I had water in my cooler with a aquarium heater heating the water as a heat source.
Last edited by zues; 05-26-2010 at 12:31 PM.
-
The Following 2 Users Say Thank You to zues For This Useful Post:
-
Registered User
Re: Were should I put the prove
When i put it on the heat source i was having to adjust to jet the 88 on the eggs, when ahead and put it in the box and have the teem I want in the box
-
-
Re: Were should I put the prove
I agree with Zues, I want to know the temp of my incubator, not my heat source. But if your egg tub touches the flexwatt directly or through water bottles I would be much more cautious. My incubator is in the freezer part of a fridge and the probe in hanging in the center of the freezer. My flexwatt does not touch the egg tub in any way. I didn't put the probe in the egg tub because the temps really aren't going to differ much, if at all, as long the temp in the fridge stays at 89.
Last edited by SlitherinSisters; 05-26-2010 at 08:09 PM.
-
The Following User Says Thank You to SlitherinSisters For This Useful Post:
martinarquero (05-26-2010)
-
BPnet Veteran
Re: Were should I put the prove
this year i had a one box incubator, i put it in the box, now my buddy has a "multi box incubator" and he put his in the incubator, but he runs fans to keep the heat moving around to all the boxes.
antreptiles
-
The Following User Says Thank You to moravaguy For This Useful Post:
martinarquero (05-26-2010)
-
Re: Were should I put the prove
Our coke cooler inc is 35 high 21 wide and 19 deep
We have 30 inches of flexwatt on the back wall with the herpstat probe placed behind the flexwatt and a fan on the floor of the inc to push air around.
We only care about the temp inside the tub since the air inside the inc isn't always the same as it is inside the tub, at least in testing it they never were exactly the same.
We use two thermometers with probes, one probe inside a tub on the top shelf and one inside a tub on the bottom shelf and double check things with a temp gun.
There are several ways to place the probe in an incubator, this one has worked great for us.
Jerry Robertson
-
The Following User Says Thank You to snakesRkewl For This Useful Post:
martinarquero (05-26-2010)
-
Registered User
Re: Were should I put the prove
Thanks to all who have answer, it's my first clutch ever so I'm all worried, temp is holding at 88.2 in the box doble checked with a termostat prove along with a hygrometer prove and then I take the temp gun they are all in the 88 range with humidity 90-95, would you say that works?
-
-
BPnet Veteran
Re: Were should I put the prove
sounds good to me remeber nothing over 93 i think it is and just lay back and relax thoese 60 days will be done soon
antreptiles
-
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|