Vote for BP.Net for the 2013 Forum of the Year! Click here for more info.

» Site Navigation

» Home
 > FAQ

» Online Users: 616

0 members and 616 guests
No Members online
Most users ever online was 47,180, 07-16-2025 at 05:30 PM.

» Today's Birthdays

None

» Stats

Members: 75,909
Threads: 249,108
Posts: 2,572,139
Top Poster: JLC (31,651)
Welcome to our newest member, KoreyBuchanan

removing UTH's from glass

Printable View

  • 11-14-2005, 12:00 PM
    sirhissball
    removing UTH's from glass
    Can this be done? I have an aquarium with two UTH's stuck to the bottom. I am switching over to plastic, and would like to not have to buy more. Any tips on trying to get these things off?
  • 11-14-2005, 12:37 PM
    justcage
    Re: removing UTH's from glass
    Take it slow:) Chances are it will ruine it, the carbon elements tend to crack when peeling and cause hot/dead spots
  • 11-14-2005, 03:32 PM
    JimiSnakes
    Re: removing UTH's from glass
    Quote:

    Can this be done? I have an aquarium with two UTH's stuck to the bottom. I am switching over to plastic, and would like to not have to buy more. Any tips on trying to get these things off?
    It can be done, but it is hard. The only ones I have ever been able to do this with are the ZooMed ones. I have had good luck with them. They don't ever seem to rip, but the others are not so good.
  • 11-14-2005, 03:37 PM
    justcage
    Re: removing UTH's from glass
    Actually the ZooMed units have a warning on the box not to remove them once attached..
  • 11-14-2005, 03:44 PM
    JimiSnakes
    Re: removing UTH's from glass
    Quote:

    Actually the ZooMed units have a warning on the box not to remove them once attached..
    Oops... :oops: that is probably for warranty purposes...but I'm not doubting you...you definitly know more about them than me. I'll admit that I have done this and had no problems with them (one I have had for over two years and I have moved it around at least twice), but if Matt says not to your best bet would be to not do it. ;)
  • 11-14-2005, 03:55 PM
    justcage
    Re: removing UTH's from glass
    Well the warrenty woudl be void but the thin carbon "strings" inside the zm's break very easily.. I woudl try it and check it out for a couple days with an IR thermometer before using it.. May be perfecty fine, but as always "safe not sorry"
  • 11-14-2005, 04:34 PM
    Sassafrass
    Re: removing UTH's from glass
    Speaking from first hand experience...DON'T DO THAT!!!

    I experimented with a UTH that was off a tank that was given to me. It was heck to get off, then it warped the steralite container, and emitted that wonderful burning plastic smell. I say experimented, because no one was living in the stearilite.

    My advice? Human heating pads. Seventeen dollars at Walgreens for the non-shut off kind.
  • 11-14-2005, 04:53 PM
    JimiSnakes
    Re: removing UTH's from glass
    Quote:

    My advice? Human heating pads. Seventeen dollars at Walgreens for the non-shut off kind.
    They are excellent, huh? Once I found out about them I was hooked.

    ~Jim
  • 11-14-2005, 05:55 PM
    TekWarren
    Re: removing UTH's from glass
    I have a couple of the zoomed pads laying around that I have stuck and re-stuck numerous times. All of them still work as good as they ever did. I still use them for temporary heat for traveling to shows and such or unexpected needed heat source. Just have to be carefull about how you remove it.
  • 11-15-2005, 11:25 PM
    recycling goddess
    Re: removing UTH's from glass
    i heard you should attach the UTH to a ceramic tile (like the kind used on your floors) and then just set the rubbermaid or glass tank on the tile (with UTH between the tile and tank)

    this way you can move it from enclosure to enclosure without breaking it.
Powered by vBadvanced CMPS v4.2.1