So the whole Rack system is actually wired down to one or two prongs? I was looking at getting a rack or build one and wasnt for sure the way the heat system was set. Right now I dont use any UTH's I just heat the room. So far I havent had any problems, but looking to upgrade the whole thing.
10-07-2013, 07:19 AM
Crazymonkee
The rack is wired to one plug that uses one port on the thermostat
Sent from my DROID RAZR using Tapatalk 4
10-07-2013, 07:22 AM
ROACH
Re: So whats better?
Quote:
Originally Posted by Crazymonkee
The rack is wired to one plug that uses one port on the thermostat
Sent from my DROID RAZR using Tapatalk 4
Cool thank you! That helps me make my mind up! Now just to come up with the $2000 to get 2 V70-11 Racks!
10-08-2013, 08:21 AM
artgecko
Yeah... That's why I opted for the 4... Although I only have 2 solo tanks at present, it'll eventually be running 1 rack for my sand boas / hognose and 1 rack for BPs, plus a couple single tanks that I may have setup. It was cheaper to buy one herpstat 4, than to buy 1 herpstat 2 now and have to buy another in a year or so when I get the racks setup.
Just make sure you do not exceed the wattage per plug and total unit wattage (I believe it gives the stats on the spyder electronics website).
10-08-2013, 08:28 AM
Crazymonkee
Re: So whats better?
Quote:
Originally Posted by artgecko
Yeah... That's why I opted for the 4... Although I only have 2 solo tanks at present, it'll eventually be running 1 rack for my sand boas / hognose and 1 rack for BPs, plus a couple single tanks that I may have setup. It was cheaper to buy one herpstat 4, than to buy 1 herpstat 2 now and have to buy another in a year or so when I get the racks setup.
Just make sure you do not exceed the wattage per plug and total unit wattage (I believe it gives the stats on the spyder electronics website).
You do know all heat sources need to be the same. Meaning... all heat tape or all heat pads or all same type of bulb...
Sent from my DROID RAZR using Tapatalk 4
10-08-2013, 04:26 PM
artgecko
Re: So whats better?
Quote:
Originally Posted by Crazymonkee
You do know all heat sources need to be the same. Meaning... all heat tape or all heat pads or all same type of bulb...
Sent from my DROID RAZR using Tapatalk 4
Crazymonkee- This is true with some thermostats... The herpstat 4 has 4 channels which each have a plug and probe. Each channel can be programmed to a different temp and even to be proportional or not, some of the channels will even do humidity as well as temp. That said, I can run a rack on one channel (with heat tape that is the same on each level of the rack) and run a tank UTH on another channel. As long as the probes and channel settings are setup correctly and I do not exceed the wattage listed, the herpstat will function correctly. Right now I am running 2 channels, each set to different temps and with different wattage UTH's and the herpstat is keeping the temps great in both tanks. That is the reason I went with the herpstat...several other multi-channel thermostats I looked at (I think the VE line was one) will only do one temperature setting for both channels.
10-08-2013, 04:35 PM
Pythonfriend
what would be more useful: if you have lets say 3 racks, would you put one rach on one channel?
or would you instead put the lower third of all racks on one channel, the middle third on one channel, and the top third on one channel?
im just thinking if a rack is on one channel, maybe its a bit too cold at the bottom and too warm at the top...
