Help me mount an incubator fan.
http://www.wax32.com/gear/incubator1.jpg
http://www.wax32.com/gear/incubator2.jpg
I need a good, and easy, way to mount this fan inside this cooler... I need a way to leave space between the back of the fan and the cooler wall. I am thinking of gorilla gluing a big nut to the four corners of the back of the fan and then mounting the fan to the side of the cooler some kind of way. I'm not real good with coming up with engineering ideas. :D
Any ideas? Thanks!
Re: Help me mount an incubator fan.
Just use some long screws. Self tapping like a long drywall screw. Don't forget to leave space so the intake side of the fan can draw air.
Maybe some tubing or nuts for spacers.
Hope that helps.
Re: Help me mount an incubator fan.
I dont really have help for your fan question but what size cooler is that? where'd you get it and how much was it?
Re: Help me mount an incubator fan.
Quote:
Originally Posted by
Dave763
Just use some long screws. Self tapping like a long drywall screw. Don't forget to leave space so the intake side of the fan can draw air.
Maybe some tubing or nuts for spacers.
Hope that helps.
Yeah I thought of that... I'd need seriously long and SKINNY screws. The holes in the fan are kinda small. I'll look into that though.
Quote:
Originally Posted by
Powerspythons
I dont really have help for your fan question but what size cooler is that? where'd you get it and how much was it?
http://www.wax32.com/gear/incubator3.jpg
$79 at wal-mart. I can fit twelve - 6qt Sterilite shoeboxes in there with room for some bottles of water to help with thermal mass.
http://www.wax32.com/gear/incubator4.jpg
Thing takes up a lot of room in my snake room. I need to clear out under that desk, I think it will slide underneath...
Re: Help me mount an incubator fan.
I used velcro, :cool:. functional and movable. .
Re: Help me mount an incubator fan.
Quote:
Originally Posted by
Snakefreak64
I used velcro, :cool:. functional and movable. .
I've been sorta thinking about that too. Did you use any special "super strength" velcro strips?
Re: Help me mount an incubator fan.
I used "L" brackets when I mounted mine. Get some small nuts and bolts and bole the "L" bracket to the fans. Then screw the other hole of the "L" bracket to the cooler wherever you want it with some small screws.
Re: Help me mount an incubator fan.
Quote:
Originally Posted by
wax32
I need a good, and easy, way to mount this fan inside this cooler... I need a way to leave space between the back of the fan and the cooler wall. I am thinking of gorilla gluing a big nut to the four corners of the back of the fan and then mounting the fan to the side of the cooler some kind of way. I'm not real good with coming up with engineering ideas. :D
Any ideas? Thanks!
I am in the process of building an incubator as well (mainly just mental right now -- no physical building yet). This is my first year breeding, and I got started a little late, so I will have to wait and see if I will even need to build an incubator.
I am planning on building just a small cooler incubator -- probably just big enough for one clutch. Would I need to put a fan in an incubator that size?
So, I was wondering about the mounting as well. The L bracket sounds like a good idea, but where to mount? It seems to me that two fans would work best in a large cooler like the original op's (one on each end?). But what about a small, single clutch cooler? Would it make sense to mount it on the middle of the lid, with the air flow blowing up? Therefore pulling up the hot air and recirculating it down? (Similar to the winter setting on a ceiling fan). Obviously there would need to be a bit of a gap between the fan and the lid.
Thanks for any thoughts!