» Site Navigation
0 members and 712 guests
No Members online
Most users ever online was 47,180, 07-16-2025 at 05:30 PM.
» Today's Birthdays
» Stats
Members: 75,904
Threads: 249,099
Posts: 2,572,074
Top Poster: JLC (31,651)
|
-
rbi rack question Please help
I have 2 CB70 4 tub RBI racks. I have a Helix thermostat.
I have the thermostat probe taped directly to the flexwat like I am supposed to.
Problem is that I have used both electrical tape AND foil tape... and both after a day or two keep coming untaped. This last attempt (the third attempt) i taped 4 different pieces of foil to hold it down. all very neatly taped.... today when I get home the rack is at 102 degrees because the dam thing came untaped again causing the probe to not be in direct contact with the flexwatt.
Getting frustrated. What am I supposed to tape the probe down with? what am i doing wrong???
Mikey Cavanaugh
(904) 318-3333
-
-
BPnet Veteran
Re: rbi rack question Please help
I use foil tape, only had a problem once. I just put 2 pieces wide over the probe and 2 piece long over that creating an approx 4"x4" square covering the probe.
-
-
Re: rbi rack question Please help
 Originally Posted by mcavana
I have 2 CB70 4 tub RBI racks. I have a Helix thermostat.
I have the thermostat probe taped directly to the flexwat like I am supposed to.
Problem is that I have used both electrical tape AND foil tape... and both after a day or two keep coming untaped. This last attempt (the third attempt) i taped 4 different pieces of foil to hold it down. all very neatly taped.... today when I get home the rack is at 102 degrees because the dam thing came untaped again causing the probe to not be in direct contact with the flexwatt.
Getting frustrated. What am I supposed to tape the probe down with? what am i doing wrong???
Electrical tape won't work for you. I have always used foil tape and have never had it come untaped. Is it coming untaped because the tub is hitting it when you slide it in/out? Foil tape is about as sticky as it gets. You could try duct tape but it's no better than foil tape. I put 1 piece across the probe, making sure that the tape is only making contact with the flexwatt. Then I put a piece longways to cover the probe completely. Then I foil tape the probe wire to the shelf so it doesn't get caught up in the tub. Hope this makes sense and helps!
-
-
BPnet Veteran
Re: rbi rack question Please help
try moving the probe to one side of the tub and adjust temps from there if the tubs are hitting it. i had that problem with a few of mine
-
-
Re: rbi rack question Please help
Have you tried asking Rich what he would recommend? He always seems very willing to help with his products when needed. I have a couple of his racks coming in next week, hopefully I won't run into this issue.
-
-
Registered User
Re: rbi rack question Please help
like the others have said use the foil tape and one across the probem and then tape the probe lengthwise. Whats happening is that your tubs are hitting the probe and pulling it loose. You will soon get it figured out and everything will be fine. Its all trial and error.
0.3 Normal, 1.1 100% Het Albino, 1.1 Yellowbelly, 1.1 Mojave
1.0 50% Het Axanthic, 1.1 Hypo, 1.0 66% Het Clown, 0.1 Black Pastel
0.1 Spider, 1.1 VPI Pastel, 1.0 Reduced Pattern, 1.0 Pinstripe
-
-
Re: rbi rack question Please help
If foil tape is coming loose, the first thing I'd do is check the surface of the flexwatt. Could be some sort of oil or residue that isn't letting the glue adhere properly. If you wipe it down with acetone it should clean off anything that might be on there.
-
-
Re: rbi rack question Please help
 Originally Posted by m00kfu
If foil tape is coming loose, the first thing I'd do is check the surface of the flexwatt. Could be some sort of oil or residue that isn't letting the glue adhere properly. If you wipe it down with acetone it should clean off anything that might be on there.
I was thinking that. a lil acetone on a rag won't mess up the tape?
Mikey Cavanaugh
(904) 318-3333
-
-
Re: rbi rack question Please help
Lets just make sure My foil tape is the same as your foil tape... My foil tape I got from home depot in the air conditioning / duct section. here it is:
http://www.findtape.com/product414/N...x?cid=12&idx=7
dam! just realized it says "cold weather" on it... specially formulated for colder temperatures... Is this the wrong tape for hot flex watt????
Mikey Cavanaugh
(904) 318-3333
-
-
Re: rbi rack question Please help
That should be fine. Good for hot or cold temps.
-
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|