» Site Navigation
3 members and 3,452 guests
Most users ever online was 6,337, 01-24-2020 at 04:30 AM.
» Today's Birthdays
» Stats
Members: 75,095
Threads: 248,538
Posts: 2,568,722
Top Poster: JLC (31,651)
Welcome to our newest member, Daisyg
|
-
UTH and foil tape
Hello all
Can you attach foil tape (sticky side) to an UTH (sticky side) and then place the heater on a plastic tub by taping the edges of the heater to the tub? I was just trying to avoid sticking the pad itself so in the future it could be move to a different container. There would be a thermostat probe sandwich between UTH with foil tape on it and the bottom of the tub.
Thanks for your time
Bodie
-
-
Yes, that would be the way to keep it reusable.
Last edited by PitOnTheProwl; 12-16-2018 at 12:57 PM.
-
-
This is from "heat tape" description on Reptile Basics:
6. If using element in contact with any metal surface, the metal surface must be grounded. A shock hazard can exist as well as the possibility of induced voltage. If using metallic (aluminum) tape to fasten element do not overlap any of the electrical areas in the element- black conductive bars or copper buss bars.
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Be safe, not sorry!
I've used Flexwatt UTH "forever" & only tape the edges (plastic only, non-electrical areas)
Last edited by Bogertophis; 12-16-2018 at 01:24 PM.
-
-
Re: UTH and foil tape
Originally Posted by Bogertophis
This is from "heat tape" description on Reptile Basics:
6. If using element in contact with any metal surface, the metal surface must be grounded. A shock hazard can exist as well as the possibility of induced voltage. If using metallic (aluminum) tape to fasten element do not overlap any of the electrical areas in the element- black conductive bars or copper buss bars.
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Be safe, not sorry!
I've used Flexwatt UTH "forever" & only tape the edges (plastic only, non-electrical areas)
Heat tape does NOT have a sticky side.
A heat mat does and is encased in a rubber insulating coating.
-
-
Re: UTH and foil tape
Thanks for the info. On this particular setup, I am not using heat tape. I am using a zoomed heat mat.
Thanks
Bodie
-
The Following User Says Thank You to Bodie For This Useful Post:
-
Re: UTH and foil tape
Originally Posted by PitOnTheProwl
Heat tape does NOT have a sticky side.
A heat mat does and is encased in a rubber insulating coating.
Yes, I know...http://www.reptilebasics.com/heat-tape
What they are saying is that if you use heat tape on metal or with metal tape, that thin cover of plastic that it's encased in is NOT enough for safety.
As I said, foil tape (if used to secure 'heat tape') should not be over any of the inner electrical connections. It can short...
Sorry, I missed that from OP what kind of UTH was meant. And I bet there's ppl using foil tape to secure "heat-tapes".
Last edited by Bogertophis; 12-16-2018 at 01:59 PM.
-
-
Re: UTH and foil tape
Originally Posted by Bogertophis
Yes, I know... http://www.reptilebasics.com/heat-tape
What they are saying is that if you use heat tape on metal or with metal tape, that thin cover of plastic that it's encased in is NOT enough for safety.
As I said, foil tape (if used to secure 'heat tape') should not be over any of the inner electrical connections. It can short...
Sorry, I missed that from OP what kind of UTH was meant. And I bet there's ppl using foil tape to secure "heat-tapes".
Actually it is. The electrical part they are talking about are the main power bars that are exposed at the cut ends. After the ends are properly insulated they are not a risk of shock or short.
-
The Following 2 Users Say Thank You to PitOnTheProwl For This Useful Post:
Godzilla78 (12-16-2018),redshepherd (12-16-2018)
-
Re: UTH and foil tape
Originally Posted by PitOnTheProwl
Actually it is. The electrical part they are talking about are the main power bars that are exposed at the cut ends. After the ends are properly insulated they are not a risk of shock or short.
yes, I have used the foil tape for a long time on the heat tape, no problems with electricity.
I DID RUN INTO ONE PROBLEM! If the metallic tape is directly contacting the thermostat probe, it gives an error code in my Herpstat. Once I made sure to keep the foil tape away from the probe, it was fine. I will use non-metallic packing tape on my heat tape from now on though.
- - - Updated - - -
Originally Posted by PitOnTheProwl
Actually it is. The electrical part they are talking about are the main power bars that are exposed at the cut ends. After the ends are properly insulated they are not a risk of shock or short.
yes, I have used the foil tape for a long time on the heat tape, no problems with electricity.
I DID RUN INTO ONE PROBLEM! If the metallic tape is directly contacting the thermostat probe, it gives an error code in my Herpstat. Once I made sure to keep the foil tape away from the probe, it was fine. I will use non-metallic packing tape on my heat tape from now on though.
-
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|