» Site Navigation
1 members and 1,277 guests
Most users ever online was 6,337, 01-24-2020 at 04:30 AM.
» Today's Birthdays
» Stats
Members: 75,093
Threads: 248,532
Posts: 2,568,688
Top Poster: JLC (31,651)
|
-
Probe flexwatt placement issue
Setup: AP rack, herpstat running flexwatt, probe placed between flexwatt and tub taped in place with electrical tape on the rack part only
Problem: probe bending and moving when tub is slid in, causing wear on probe and potential dislodgement
Plan: use dremel to expand existing channel for probe so it can reach flexwatt directly, tape probe to the flexwatt directly
Question: is there a problem with taping the probe onto the flexwatt? Could this cause a misreading of the temperature? Melt something? Is electrical tape ok?
Thanks!
-Devon
0.1 Axanthic Bee (Pixel)
0.2 Axanthic Pastel (Cornelia, Short Round)
0.1 Axanthic (Bubbles)
0.1 Bee het Axanthic (Nipper)
0.1 Lesser (Lydia)
0.1 het Lavender (Poppy)
0.1 het Hypo (Cookie)
1.0 Killerbee het Axanthic (Yellow Dude)
1.0 Pied (Starry Starry Dude)
1.0 Butter Hypo (Spooky Dude)
1.0 PH Lavender (Little Dude)
-
-
Regardless of what anyone else says:
I use foil tape to tape my probe to the back of the shelf on the flex-a-watt.
Then again I have a tub set up with a thermometer in it that I rotate through the rack every couple weeks to make sure that all my shelves are heating.
I adjust the thermostat to in tub temps according to the thermometer tub
All my racks are home made.
Your AP rack should have one long strand of flex-a-watt weaved through it, right?
Can you put the probe on the side of the tub where it goes up to the next shelf?
-
-
I don't recommend using foil tape on the probe directly has this can cause false readings.
http://spyderrobotics.com/products/herpstat12_manual.pdf
Sent from my iPhone 5 using Tapatalk
Last edited by martin82531; 12-31-2012 at 01:16 PM.
0.0.1 Normal Ball Python
1.0 Albino Ball Python
0.1 Het Snow BCI
1.0 Lesser Ball Python
-
-
What do you recommend then?
-
-
Originally Posted by 3skulls
What do you recommend then?
Can you put the probe under the flexwatt then tape the flexwatt down?
Sent from my iPhone 5 using Tapatalk
0.0.1 Normal Ball Python
1.0 Albino Ball Python
0.1 Het Snow BCI
1.0 Lesser Ball Python
-
-
My main concern is having tape in contact with the flexwatt, is there a safety hazard with doing that? If not, is one type of tape better than another?
-Devon
0.1 Axanthic Bee (Pixel)
0.2 Axanthic Pastel (Cornelia, Short Round)
0.1 Axanthic (Bubbles)
0.1 Bee het Axanthic (Nipper)
0.1 Lesser (Lydia)
0.1 het Lavender (Poppy)
0.1 het Hypo (Cookie)
1.0 Killerbee het Axanthic (Yellow Dude)
1.0 Pied (Starry Starry Dude)
1.0 Butter Hypo (Spooky Dude)
1.0 PH Lavender (Little Dude)
-
-
Tape is perfectly fine on the flexwatt. This is not my picture but this is 100% a mirror image how I have my flexwatt taped to my ap pvc enclosure.
I would recommend foil tape, I get mine from reptile basics.
http://www.reptilebasics.com/aluminum-foil-tape
Sent from my iPhone 5 using Tapatalk
0.0.1 Normal Ball Python
1.0 Albino Ball Python
0.1 Het Snow BCI
1.0 Lesser Ball Python
-
-
Just curious why the flexwatt is taped to the middle instead of in the channel?
-Devon
0.1 Axanthic Bee (Pixel)
0.2 Axanthic Pastel (Cornelia, Short Round)
0.1 Axanthic (Bubbles)
0.1 Bee het Axanthic (Nipper)
0.1 Lesser (Lydia)
0.1 het Lavender (Poppy)
0.1 het Hypo (Cookie)
1.0 Killerbee het Axanthic (Yellow Dude)
1.0 Pied (Starry Starry Dude)
1.0 Butter Hypo (Spooky Dude)
1.0 PH Lavender (Little Dude)
-
-
You can also get aluminum tape at lowes, home depot, or any other hardware store.
-
-
Re: Probe flexwatt placement issue
Originally Posted by PitOnTheProwl
Regardless of what anyone else says:
I use foil tape to tape my probe to the back of the shelf on the flex-a-watt.
Then again I have a tub set up with a thermometer in it that I rotate through the rack every couple weeks to make sure that all my shelves are heating.
I adjust the thermostat to in tub temps according to the thermometer tub
All my racks are home made.
Your AP rack should have one long strand of flex-a-watt weaved through it, right?
Can you put the probe on the side of the tub where it goes up to the next shelf?
It does have the long strand, but I've noticed that when there's no tub on top of the probe the temperature disparity between the probe reading and the temp in the tub goes up to around 10 degrees. I want to keep them as close as possible. I am also doing the rotating thermometer check, it's interesting to see the variation up and down the rack.
-Devon
0.1 Axanthic Bee (Pixel)
0.2 Axanthic Pastel (Cornelia, Short Round)
0.1 Axanthic (Bubbles)
0.1 Bee het Axanthic (Nipper)
0.1 Lesser (Lydia)
0.1 het Lavender (Poppy)
0.1 het Hypo (Cookie)
1.0 Killerbee het Axanthic (Yellow Dude)
1.0 Pied (Starry Starry Dude)
1.0 Butter Hypo (Spooky Dude)
1.0 PH Lavender (Little Dude)
-
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|