Vote for BP.Net for the 2013 Forum of the Year! Click here for more info.

» Site Navigation

» Home
 > FAQ

» Online Users: 523

1 members and 522 guests
Most users ever online was 6,337, 01-24-2020 at 04:30 AM.

» Today's Birthdays

Ziggy31984 (40)

» Stats

Members: 75,014
Threads: 248,474
Posts: 2,568,391
Top Poster: JLC (31,651)
Welcome to our newest member, DetectiveIcarus
Page 1 of 7 1234567 LastLast
Results 1 to 10 of 64
  1. #1
    BPnet Lifer Vypyrz's Avatar
    Join Date
    04-13-2009
    Location
    Morehead City, North Carolina
    Posts
    5,528
    Thanks
    554
    Thanked 1,800 Times in 1,267 Posts
    Images: 38

    Vypyrz Tub Set-Up, The Basics...*DUW*

    The purpose of this thread is not to perpetuate the continuous debate of "Tanks vs. Tubs", but to try and both answer and illustrate as much as I can about stand alone tubs and their set-up. There are many different alternatives, options, and methods to doing things, and I will try to list some where applicable.
    Since websites and products can change or vary, depending on your location, I am not including any external links in this thread. If you have a question on where to purchase supplies, please ask in a separate thread so that current information can be provided.

    Some Notes On Tubs:

    Humidity- While it is generally easier to regulate and maintain the humidity levels in tubs, there are several factors that will affect it and should be considered. These are:
    1) Your geographic location.
    2) Ambient environmental conditions in your home.
    3) Number of holes in the tub.
    4) Size of the holes.
    5) Ventilation
    6) Size of the water bowl.
    7) Type of substrate used.
    The amount of ventilation is the key to regulating humidity. This is all dependant on the number and size of the holes and the amount of airflow through the tub. I recommend starting out with just a few holes. After the humidity stabilizes, add a few more holes at a time until it gets to the level that you want it at. Depending on the seasonal weather at your location, you may have to open quite a few more holes in the summer and then cover some during the winter months. Or, you can use two different tubs. Another way to regulate the humidity is to increase or decrease the amount of air flow through the tub. This can be accomplished by the use of an oscillating fan, or, in some cases, a cieling fan, if available. If you choose this method, then you adjust the speed and position of the fan to change the humidity.

    Temperature- I normally recommend that the size of the heat source cover at least 1/3 but not more than 1/2 of the floor space of the tub. The ambient room temp will affect the tub temperture. If your house generally stays at or above 75F, then you can probably use a heat source size on the lower end of the range. If your house stays below 75F, then you may want to use a heat source size closer to the upper end of the range. If you live in a really cold place, then you might decide to use a dual heat source/thermostat set-up. Another option is to use a space heater to maintain the ambient temperature in the room where your snake is kept.

    Heat Sources- Here, you have basically two choices, Under Tank Heater(UTH) pads and Flexwatt Heat Tape. Both can be obtained in a variety of sizes and configurations and it's your preference whichever one you choose.

    Thermostats- Please, please, do not use an un-regulated heat source. Sooner or later, you will run into trouble because of it. A thermostat will save you from alot of frustration, heartache, and money in the long run. A rheostat or dimmer can be used in a pinch, however, these do not regulate heat, they only adjust it. These require closer monitoring and more frequent adjustments since the tub temperatures will change with changes in the house temps. The $25-$30 investment in a basic thermostat will save you a $300+ trip to the vet due to a burned snake.

    Selecting Tub Size- Depending on who you ask, you will get a variety of recommendations on "tub size vs. snake size." Since most stand alone tubs are translucent in varying degrees, depending on brand and model, I prefer to set mine up the same as a tank with a minimum of two hides and a water bowl, and this is how I determine the size of the tub:
    1) Decide what size of snake you want (juvenile, adult, etc.) or pick out your particular snake.
    2) Select two appropriately sized and snug hides for your snake, a water bowl, and any extras, such as a small branch or fake rock for rubbing on.
    3) Now that you have the furnishings, find a tub that all of the items will fit comfortably in. They don't have to be crammed into the tub, but you don't want alot of extra space. For younger snakes, I figure about 3-5 inches of floor space between items is ok. For larger snakes, you can give them a little more room. Don't get a tub that is too tall for your snake. For Ball Pythons and most ground dwelling snakes, the 6-7 inch tall tubs are about perfect.
    4) Once you have the tub selected, now you can get the correct size heat source.

    Setting It Up-

    Here is what you need to get started:




    1) Tub
    2) Heat Source (UTH or Flexwatt)
    3) Thermostat
    4) 2 Thermometers (one with a probe) or Temp gun, and a Hygrometer. I like the Acu-Rite because it measures two temperatures and humidity all in one unit.
    5) Soldering Iron, Drill, Wood Burning Iron, or whatever you decide to make the holes with. I prefer a soldering iron.
    6) Tape. I use aluminum tape because it is generally easier to remove.
    7) Binder Clips
    8) Velcro (Optional)
    9) Luggage Strap or Bungee Cord (Optional)
    10) Substrate
    11) Water Bowl
    12) 2 Hides. This is two small litter pans and 2 plastic bowls which can easily be made into cheap, adequate hides by melting an entrance hole on the side with the soldering iron. Keep in mind that whether you choose to purchase or make your own hides, they should provide a snug fit for your snakes security.

    - Decide how many holes you want to start off with and where you want to place them. If you want to lay them out in a fancy pattern, it's your prerogative. I only put holes on the front and back, because that is all I need.



    - Make the holes.



    -Turn the tub upside down so that you are looking at the bottom. Mount the Thermostat probe to the bottom of the tub with a piece of tape.



    - Using tape, mount the UTH over the probe. Some Heaters come with little rubber feet to raise the enclosure. If yours doesn't, you can use something like thin pieces of wood or by glueing a plastic bottle cap at each corner. This is to keep the heat source from contacting the surface below, or, if your tub is not indented on the bottom, it will keep it from wobbling on the probe.



    - Flip the tub over. Next comes the thermometer. The base unit will go on the cool side and will tell you the ambient temperature and humidity level. The probe will be placed on the warm side, against the bottom of the tub, over the UTH. This will tell you what the hottest temperature that your snake will be exposed to, should they burrow in or under the substrate. If you don't have velcro, you can just set the unit in the tub. I prefer to apply velcro to the back of it and mount it to the side of the tub.





    - The excess probe wire can be buried under the substrate.



    - But I prefer to keep it out of the way by melting a hole near the bottom of the warm side and running the probe out, around, and back in on the warm side. That way, all of the excess wire stays tucked away behind the tub and out of the way. I use a few globs of hot glue to hold it in place.



    - Add the substrate, furnishings, and water.



    - The Binder Clips are used to pinch the tub and lid together to close any gaps and reduce the chance for an escape. I also use luggage straps on my tubs, even though they are really only needed on one tub. I just like everything uniform.

    -At this point, connect the UTH to the thermostat and set it to the desired temperature. Monitor the temps and humidity inside the tub for a few hours. Make small adjustments to the holes and/or ventilation for the humidity levels, and depending on what the inside temps are doing, you may need to adjust the thermostat setting a little. Once all of your numbers are good and stabilized...go get your snake.

    Hopefully, this will answer some questions and provide some of the basics of setting up a stand alone tub.

    Since mounting the thermostat probe and heat source to the bottom of the tub can be a bit cumbersome when it comes to moving the tub for cleaning, you can mount the heat source and probe so that they are not physically attached to the tub. I chose to make a mounting base.

    I decided to use Melamine, and bought 2 shelves (4' X 18"), which is what I needed for my four tubs.
    *NOTE* If you do not have a power saw to cut the Melamine, I suggest having it cut at the place of purchase.
    I measured and cut each shelf into 4 pieces, so I had a total of:
    4 pieces, 18" X 18"
    4 pieces, 18" X 6"
    Which gave me one set per tub.



    My first thought was to just mount the UTH to the base with the probe on top, so I mocked it up to see what it would look like. While this will work effectively, I wanted something a little different.





    I wanted a way to securely mount the probes where they would also be protected. I measured the diameter of the probes at 3/8". I then hooked up the router attachment to my Dremel tool and set it for 3/16" and cut a channel in each of the bases. This would allow the probe to be recessed into the base but still be in direct contact with the UTH.





    Since the shelves are grated, the best way I could come up with to hold the bases in place was the tried and true duct tape, followed by the probes, and then the UTH's.





    In order to keep the wires from shifting or pulling out, I mounted them in place using the wire clamps.



    This is my end result:



    -Vypyrz-
    "Cry, Havoc! And let slip the dogs of war..."

  2. The Following 73 Users Say Thank You to Vypyrz For This Useful Post:

    + Show/Hide list of the thanked

    American (07-25-2013),Andybill (03-08-2012),angllady2 (02-19-2011),Anya (06-09-2011),Badgemash (09-17-2012),BallPythonLove (05-17-2012),ballpythonluvr (02-19-2011),bcr229 (01-27-2021),BeansTheDerp (01-27-2021),BFT12890 (12-16-2011),BLM94 (05-23-2012),Bluedevil0584 (01-10-2019),Booper (02-27-2018),BPSnakeLady (11-05-2014),bx718 (12-31-2012),Capray (05-18-2012),CaptainKillua (12-12-2017),cecilbturtle (04-10-2011),cmack91 (11-25-2011),CoolioTiffany (11-11-2011),DellaF (02-20-2011),dizzydynamo (07-01-2011),DooLittle (03-04-2012),Evan00 (12-09-2011),ewaldrep (09-18-2012),Fidget (05-31-2012),greco (11-01-2013),halfnakedlife (02-22-2017),influence (01-10-2015),Jenn62501 (12-30-2011),Jessica Loesch (11-11-2011),jplehmann (11-02-2014),jsmorphs2 (02-21-2011),Juliemay13 (04-10-2011),Kaali (04-20-2016),kuppler (05-17-2012),Kymberli (04-10-2011),L.West (02-20-2011),macho9714 (06-06-2012),martin82531 (11-06-2012),Megg (09-30-2015),Mira-icy (10-22-2011),MissDizzyBee (04-09-2011),Mitch (02-27-2011),Monty44 (09-07-2017),moonlightgdess (03-04-2012),MrBrute (10-29-2012),Oregonism (06-05-2015),OR_Hippy (06-29-2014),pastelballs (01-17-2016),Pickenprod (12-05-2011),pigfat (12-06-2011),pixiepup (09-08-2016),Popeye (05-11-2011),Ridinandreptiles (11-04-2012),RoyalNoob (02-05-2017),RoyaLoveRay (01-24-2015),sciencemuse (11-27-2011),se7en (01-16-2015),shadowsnakes (08-01-2013),slackerz (01-04-2012),sparky767 (02-16-2018),Spechal (05-18-2018),Strange_Evil (02-19-2011),Sunbreeze327 (02-01-2012),texanborn (04-13-2011),towelie4365 (04-17-2012),Trackstrong83 (02-22-2012),unmei (05-18-2012),WarriorPrincess90 (06-19-2012),wytchling (10-14-2011),yeroc1982 (02-19-2011),Zoodledoodle (07-02-2013)

  3. #2
    BPnet Royalty ballpythonluvr's Avatar
    Join Date
    11-23-2008
    Location
    Pennsylvania
    Posts
    8,062
    Thanks
    4,207
    Thanked 3,152 Times in 2,887 Posts
    Images: 6

    Re: Vypyrz Tub Set-Up, The Basics...*DUW*

    Thank you for this Vyprz! I am about to get another snake and I am making the switch to tubs! This is very helpful and couldn't have been posted at a better time!

  4. The Following User Says Thank You to ballpythonluvr For This Useful Post:

    Vypyrz (02-22-2011)

  5. #3
    BPnet Veteran yeroc1982's Avatar
    Join Date
    07-25-2010
    Posts
    684
    Thanks
    171
    Thanked 51 Times in 50 Posts
    Nice write up!

  6. The Following User Says Thank You to yeroc1982 For This Useful Post:

    Vypyrz (02-22-2011)

  7. #4
    Registered User Strange_Evil's Avatar
    Join Date
    12-31-2010
    Location
    Westchester, New York
    Posts
    199
    Thanks
    50
    Thanked 35 Times in 30 Posts
    Images: 21
    This is really well illustrated and detailed. Great job
    Why? Why do humans always look to the sky? Why do you try so hard to fly when you don't have any wings? We'll run on our own legs. - Kiba "Wolf's rain"

  8. The Following User Says Thank You to Strange_Evil For This Useful Post:

    Vypyrz (02-22-2011)

  9. #5
    BPnet Veteran RichieBoo's Avatar
    Join Date
    07-13-2010
    Location
    Long Island,New York
    Posts
    934
    Thanks
    519
    Thanked 234 Times in 186 Posts
    Images: 14

    Re: Vypyrz Tub Set-Up, The Basics...*DUW*

    Hi Vypyrz very helpful post..the black hides in your tub set up are what size and are they from reptile basics..what size tub is that...

  10. #6
    BPnet Lifer Vypyrz's Avatar
    Join Date
    04-13-2009
    Location
    Morehead City, North Carolina
    Posts
    5,528
    Thanks
    554
    Thanked 1,800 Times in 1,267 Posts
    Images: 38

    Re: Vypyrz Tub Set-Up, The Basics...*DUW*

    Quote Originally Posted by RichieBoo View Post
    Hi Vypyrz very helpful post..the black hides in your tub set up are what size and are they from reptile basics..what size tub is that...
    Yes, they are Reptile Basics hides and they are the Medium size. That particular tub is a 32 quart tub.
    "Cry, Havoc! And let slip the dogs of war..."

  11. The Following 2 Users Say Thank You to Vypyrz For This Useful Post:

    mike34 (12-07-2015),RichieBoo (02-20-2011)

  12. #7
    BPnet Veteran 2kdime's Avatar
    Join Date
    06-22-2007
    Location
    Missouri
    Posts
    4,027
    Thanks
    649
    Thanked 806 Times in 660 Posts
    Images: 21
    From experience, that sticky velcro is ten times stickier than duct tape and ten times as harmful when they knock it loose and get it stuck to them.

  13. The Following User Says Thank You to 2kdime For This Useful Post:

    cecilbturtle (04-10-2011)

  14. #8
    BPnet Lifer Vypyrz's Avatar
    Join Date
    04-13-2009
    Location
    Morehead City, North Carolina
    Posts
    5,528
    Thanks
    554
    Thanked 1,800 Times in 1,267 Posts
    Images: 38

    Re: Vypyrz Tub Set-Up, The Basics...*DUW*

    I do have another way that can be used to mount the Acu-Rite type thermometers. I'll see if I have some half way decent pics of it.
    "Cry, Havoc! And let slip the dogs of war..."

  15. #9
    BPnet Lifer Vypyrz's Avatar
    Join Date
    04-13-2009
    Location
    Morehead City, North Carolina
    Posts
    5,528
    Thanks
    554
    Thanked 1,800 Times in 1,267 Posts
    Images: 38

    Re: Vypyrz Tub Set-Up, The Basics...*DUW*

    If you are using an Acu-Rite thermometer, or something similar with a hanging slot on the back, here is another way to mount it using standard hardware. These aren't the greatest photos because my camera doesn't do close-ups very well.

    You will need the following:
    1- screw
    2-washers
    2-nuts
    The screw head should be small enough for it to fit in the hanging slot and, depending on the size of your holes, the washers should be big enough to keep the nuts from passing through the holes.



    First, take one of the nuts and put it on the screw approximately 1/8" or so from the head, then add a washer.



    Insert the screw through the hole that you are using.



    Add the other washer and then the nut and tighten down.

    "Cry, Havoc! And let slip the dogs of war..."

  16. The Following User Says Thank You to Vypyrz For This Useful Post:

    Monty44 (09-07-2017)

  17. #10
    BPnet Veteran 2kdime's Avatar
    Join Date
    06-22-2007
    Location
    Missouri
    Posts
    4,027
    Thanks
    649
    Thanked 806 Times in 660 Posts
    Images: 21
    Good idea there too

    I like these better when I find that I want to use one and get them at Wally World as well

    I just temp gun the hot spot when I need to know what its at.

    http://www.klockit.com/products/dept-64__sku-32297.html

Page 1 of 7 1234567 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBadvanced CMPS v4.2.1