Radiant Heat Panel - DIY

Here are plans for DIY heat panels. I would suggest using Flexwatt for the heat element, but other options can be found here:
http://www.goldmine-elec-products.co....asp?dept=1196
http://www.allelectronics.com/cgi-bi...c_Coolers.html
Any element that doesn't run on 110v standard power has to be properly wired and run through an on/off thermostat. That's why Flexwatt is probably the best option for most people.

Materials:
Flexwatt
Flexwall connectors (Solder, clamps, male terminal connectors, etc.)
Extension cord
Reflectix
1/8" - 3/16" plexiglass or acrylic sheet w/ Weld-on acrylic cement or 2-part epoxy OR 1/8" - 1/4" hardwood sheet and wood glue.
Nylon screen mesh
Drill and hole cutter bit (1"-3" diameter) and 3/8" drill bit
Gorrilla Glue
Sticky backed velcro tabs

Step 1. Measure the dimensions of the side of the enclosure where you plan to put the heat tape, and decide what size you want the radiant heat panel to be.

Note: If you are using 11" Flexwatt, the panels should be 12" X (any length. You can use multiple rows of any width Flexwatt, but keep that size in mind when determining the widhe of the heat panel. A 16" x 16" heat panel won't be any more effective than an 11" x 16" panel if the element is only 11".

Step 2. Cut 2 equal size panels from the wood or acrylic to the size you determined before.

http://www.inkednation.com/images/us...7283174716.jpg

Step 3. Cut 4 panels to be the top, bottom and sides, to fit flush on the inside of the front and back panels, all 3/4" deep.

Step 4. Drill a 3/8" hole in the center of the TOP panel.

Step 5. Attach the BACK, sides, top and bottom using whatever method of construction you decided on, based on the panel material.

http://www.inkednation.com/images/us...7283174815.jpg

Step 6. Line the entire inside back with the Reflectix and secure with thin rows of Gorrilla glue.

http://www.inkednation.com/images/us...7283174729.jpg

Step 7. Cut the end off of the extension cord, separate the end down to about 10" and strip the insulation off both wires of the exposed end.

Step 8. Push the stripped end of the wires, from the outside, through the hole you drilled and connect the cord to the Flexwatt.

Step 9. Use a few dabs of Gorilla glue to attach the Flexwatt to the Reflectix. ONLY GLUE ON THE OUTSIDE PLASTIC STRIPS.

Step 10. Use the drill with the circle cutter bit to drill evenly spaced circles in the FRONT panel. Leave 1/2" around the edges of the panel. I suggest making a paper template, or measuring and marking, to make evenly spaced holes. They will be visable.

http://www.inkednation.com/images/us...7283174742.jpg

Step 11. Put a bead of glue around each hole and attach a piece of the nylon screen that's 1/2" shorter than the panels. That will be the inside front.

http://www.inkednation.com/images/us...7283174755.jpg

Step 12. When all the glue is dry, attach the front panel (Screen side in) to the box. You might want to test it first, to make sure the tape is wired correctly.

Step 13. Use some gorilla glue to attach some velco tabs to the back. These will make it easier to mount and remove the heat panel during cage cleaning. The back of the velcro tabs can be attached to the inside of a glass enclosure using the pre applied adhesive.

http://www.inkednation.com/images/us...0728317485.jpg

That's it. Plug this right into a thermostat. If you want you can paint it or apply heat shrink film coating used on R/C planes to make it more asthetically pleasing, but if you paint it, do the front panel before attaching the screen.

Awesome DIY.

Question on step 10 - about drilling holes could you use peg board instead (save the work)? If so would the nylon screen still be needed (as I assume it is to keep the snake away from the flex)?

Hell yeah it could. I guess. I kind of just thought this up as I was typing and drawing. A pegboard front would save some time and probably output heat a little more evenly. You probably wouldn't need the nylon screen either. Good tip.

You must spread some Reputation around before giving it to PythonWallace again.

Well I can't give you rep so I'll just say it here, that's awesome!

Quote:

---

Originally Posted by Holbeird

You must spread some Reputation around before giving it to PythonWallace again.


Well I can't give you rep so I'll just say it here, that's awesome!

---

I hooked him up :sweeet:

Thanks! Last night I thought of an easier, only slightly ghetto way to make these using two Sterilite lids glued together to house the guts. Everything else would be the same, except it would be plastic and you could make one in about 15 minutes. I think I'm going to start making some of these.

seeing how im making a enclosure 7ft long and is gonna be pretty big for my 7 foot burm, this is awesome! belly heat is taken care of but as far as ambient, i really didnt want to buy a expensive heat panel.. thanks alot! saved me some $$$$...


I say we Sticky this :)

Thanks. Yeah making your own 6'-7' heat panel should save you a lot of money.