Question about a Tub

[HerpsForDerps]

Hello everyone!

I just had a quick question regarding building a tub. I have all of the materials besides aluminum tape that is recommended in the sticky for building a tub. Would duct tape be fine (just for use with the thermostat probe and the UTH)? Or would the heat be too much? I currently have the thermostat set to 90 degrees Fahrenheit. Is that a good temperature?

Thank you in advance for any help you can provide!

-Christian

[Elite Morphs]

i used duct tape before and it dont really work the heat pad will start to melt it and it will get all sticky so i would not use it

[DooLittle]

I wouldn't use it. It will become a sticky mess. You should be able to get the aluminum tape at a variety of stores.

[Royal Hijinx]

The thermostat temp will depend on what your temp gun is reading on the inside of the tub.

The duct tape will become a mess. Lowes or Home Depot sells the tape you need. I know it sucks to buy a roll for a tub, but it will last you a long time and has other uses around the house.

[Homegrownscales]

I promise eventually you will go through that roll of aluminum tape. I use it everywhere.


Check out what's new on my website... www.Homegrownscales.com

[HerpsForDerps]

Thanks for the help guys! Went out and bought a roll today and got my tub all set up. I have my UTH set to 96 Fahrenheit right now but am only getting 86/76 with 61% humidity in a 28 quart Sterilite tub. I have a small water bowl in the back with two hides (one on each side) and am using Aspen for my substrate. Would it be bad to up the temperature on my thermostat? I have the thermostat's probe directly under the UTH under the tank and my thermometer's probe on the inside of the tank over the UTH. I am using a 20g zilla UTH from Petco. Also is 61% humidity too high? Should I add a few more ventilation holes?

[The Serpent Merchant]

My cages stay at 60% humidity all the time. No problems at all.

How thick is the layer of aspen? UTH's need a substrate layer of 1/2" or less to be effective.

If the floor of the tub is below 92 turn up the UTH.

[KatStoverReptiles]

My cages stay at 60% humidity all the time. No problems at all.

How thick is the layer of aspen? UTH's need a substrate layer of 1/2" or less to be effective.

If the floor of the tub is below 92 turn up the UTH.

Aaron makes a good point. Where are you taking the temperature from? Be sure to take it from under the substrate as your snake can and will burrow down in it and be exposed to that temperature.

[travis11]

If you want to use Duct Tape, they have a heat resistant tape which is good for up to 200 degrees and its perfectly fine. Your UTH will and should never get that hot if regulated. This will not melt.

[HerpsForDerps]

I have the probe of the Thermometer under the substrate directly above the UTH on the bottom of the interior of the tub. Is there any limit that I should not go above for the Thermostat's setting? For example if it takes a setting of 100-102 to get the 90-92 in the bottom of the tank would that be ok?

Also my cool side dropped down to right around 75 during the night. Should I look at a little heater to put on top of the desk near the tub?

I have between 1/2 inch to 1 inch of substrate in the tub right now so when I get home later I'll take some out so the UTH can be more effective.

Also the humidity went up quite a bit to mid 70s. I took the top off and aired it out a bit this morning before I had to leave for school. Going to add more holes for ventilation later tonight. Do the ventilation holes have to be on the side of the tub or would it be ok for me to add some to the top?